124 lines
3.8 KiB
Arduino
124 lines
3.8 KiB
Arduino
|
/*
|
||
|
|
Web Server
|
||
|
|
|
||
|
|
A simple web server that shows the value of the analog input pins.
|
||
|
|
using an Arduino Wiznet Ethernet shield.
|
||
|
|
|
||
|
|
Circuit:
|
||
|
|
* Ethernet shield attached to pins 10, 11, 12, 13
|
||
|
|
* Analog inputs attached to pins A0 through A5 (optional)
|
||
|
|
|
||
|
|
created 18 Dec 2009
|
||
|
|
by David A. Mellis
|
||
|
|
modified 9 Apr 2012
|
||
|
|
by Tom Igoe
|
||
|
|
modified 02 Sept 2015
|
||
|
|
by Arturo Guadalupi
|
||
|
|
|
||
|
|
*/
|
||
|
|
|
||
|
|
#include <SPI.h>
|
||
|
|
#include <Ethernet.h>
|
||
|
|
|
||
|
|
// Enter a MAC address and IP address for your controller below.
|
||
|
|
// The IP address will be dependent on your local network:
|
||
|
|
byte mac[] = {
|
||
|
|
0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED
|
||
|
|
};
|
||
|
|
IPAddress ip(192, 168, 1, 177);
|
||
|
|
|
||
|
|
// Initialize the Ethernet server library
|
||
|
|
// with the IP address and port you want to use
|
||
|
|
// (port 80 is default for HTTP):
|
||
|
|
EthernetServer server(80);
|
||
|
|
|
||
|
|
void setup() {
|
||
|
|
// You can use Ethernet.init(pin) to configure the CS pin
|
||
|
|
//Ethernet.init(10); // Most Arduino shields
|
||
|
|
//Ethernet.init(5); // MKR ETH shield
|
||
|
|
//Ethernet.init(0); // Teensy 2.0
|
||
|
|
//Ethernet.init(20); // Teensy++ 2.0
|
||
|
|
//Ethernet.init(15); // ESP8266 with Adafruit Featherwing Ethernet
|
||
|
|
//Ethernet.init(33); // ESP32 with Adafruit Featherwing Ethernet
|
||
|
|
|
||
|
|
// Open serial communications and wait for port to open:
|
||
|
|
Serial.begin(9600);
|
||
|
|
while (!Serial) {
|
||
|
|
; // wait for serial port to connect. Needed for native USB port only
|
||
|
|
}
|
||
|
|
Serial.println("Ethernet WebServer Example");
|
||
|
|
|
||
|
|
// start the Ethernet connection and the server:
|
||
|
|
Ethernet.begin(mac, ip);
|
||
|
|
|
||
|
|
// Check for Ethernet hardware present
|
||
|
|
if (Ethernet.hardwareStatus() == EthernetNoHardware) {
|
||
|
|
Serial.println("Ethernet shield was not found. Sorry, can't run without hardware. :(");
|
||
|
|
while (true) {
|
||
|
|
delay(1); // do nothing, no point running without Ethernet hardware
|
||
|
|
}
|
||
|
|
}
|
||
|
|
if (Ethernet.linkStatus() == LinkOFF) {
|
||
|
|
Serial.println("Ethernet cable is not connected.");
|
||
|
|
}
|
||
|
|
|
||
|
|
// start the server
|
||
|
|
server.begin();
|
||
|
|
Serial.print("server is at ");
|
||
|
|
Serial.println(Ethernet.localIP());
|
||
|
|
}
|
||
|
|
|
||
|
|
|
||
|
|
void loop() {
|
||
|
|
// listen for incoming clients
|
||
|
|
EthernetClient client = server.available();
|
||
|
|
if (client) {
|
||
|
|
Serial.println("new client");
|
||
|
|
// an http request ends with a blank line
|
||
|
|
boolean currentLineIsBlank = true;
|
||
|
|
while (client.connected()) {
|
||
|
|
if (client.available()) {
|
||
|
|
char c = client.read();
|
||
|
|
Serial.write(c);
|
||
|
|
// if you've gotten to the end of the line (received a newline
|
||
|
|
// character) and the line is blank, the http request has ended,
|
||
|
|
// so you can send a reply
|
||
|
|
if (c == '\n' && currentLineIsBlank) {
|
||
|
|
// send a standard http response header
|
||
|
|
client.println("HTTP/1.1 200 OK");
|
||
|
|
client.println("Content-Type: text/html");
|
||
|
|
client.println("Connection: close"); // the connection will be closed after completion of the response
|
||
|
|
client.println("Refresh: 5"); // refresh the page automatically every 5 sec
|
||
|
|
client.println();
|
||
|
|
client.println("<!DOCTYPE HTML>");
|
||
|
|
client.println("<html>");
|
||
|
|
// output the value of each analog input pin
|
||
|
|
for (int analogChannel = 0; analogChannel < 6; analogChannel++) {
|
||
|
|
int sensorReading = analogRead(analogChannel);
|
||
|
|
client.print("analog input ");
|
||
|
|
client.print(analogChannel);
|
||
|
|
client.print(" is ");
|
||
|
|
client.print(sensorReading);
|
||
|
|
client.println("<br />");
|
||
|
|
}
|
||
|
|
client.println("</html>");
|
||
|
|
break;
|
||
|
|
}
|
||
|
|
if (c == '\n') {
|
||
|
|
// you're starting a new line
|
||
|
|
currentLineIsBlank = true;
|
||
|
|
} else if (c != '\r') {
|
||
|
|
// you've gotten a character on the current line
|
||
|
|
currentLineIsBlank = false;
|
||
|
|
}
|
||
|
|
}
|
||
|
|
}
|
||
|
|
// give the web browser time to receive the data
|
||
|
|
delay(1);
|
||
|
|
// close the connection:
|
||
|
|
client.stop();
|
||
|
|
Serial.println("client disconnected");
|
||
|
|
}
|
||
|
|
}
|
||
|
|
|